Dit artikel wordt momenteel naar het Nederlands vertaald en kan deels nog in het Engels geschreven zijn.
If you wish to download this article as a PDF, please scroll to the bottom of the page or click HERE.
Deel dit artikel:
Communicatie Poorten voor Batterij-aansluiting
Aangezien de vraag naar schone en betrouwbare energieoplossingen blijft groeien, is de compatibiliteit van Solis omvormers met batterijen van verschillende fabrikanten een cruciale zorg geworden voor degenen die veelzijdige en efficiënte energieopslagoplossingen zoeken. In dit artikel zullen we ingaan op de verschillende methoden en overwegingen voor het naadloos aansluiten van Solis omvormers op batterijen van meerdere fabrikanten, zodat u uw energieopslagsysteem kunt aanpassen aan uw unieke eisen.
Als u de batterij met Solis omvormers wilt verbinden, zijn de communicatiepoorten aan de kant van de omvormer als volgt:
CAN-H (Controller Area Network High) op Pin 4 (blauw)
CAN-L (Controller Area Network Low) op Pin 5 (blauw/wit)
Als u de CAN-communicatiedetails voor uw batterijen wilt begrijpen, verwijzen wij graag naar de afzonderlijke batterijhandleidingen die door elke batterijfabrikant worden verstrekt. Verschillende merken kunnen unieke specificaties en eisen hebben voor CAN-communicatie, dus het is belangrijk om de specifieke documentatie te raadplegen voor de batterijen die u gebruikt.
We begrijpen dat dit complex kan zijn. Om u te helpen hebben we een lijst samengesteld met communicatie-aansluitdetails voor verschillende batterijfabrikanten.
Hoog Voltage Batterijen (voor S6-EH3P(5-10)K-H-EU en RHI-3P(5-10)K-HVES-5G omvormers):
(Klik op de links om naar de batterij te gaan)
- BYD (Battery-Box-Premium - HVS/HVM)
- Pylon (Force-H2)
- Soluna (Module 10K Pack HV)
- Weco (WeCo5K3-LV-HV)
- Dyness (Tower Series)
- LG Energy Solutions (Resu 10H Prime)
Laag Voltage Batterijen (voor RHI-(3-4.6)K-48ES-5G, S5-EH1P(3-6)K-L en S6-EA1P(3.6-6)K-L omvormers):
(Klik op de links om naar de batterij te gaan)
- BYD (Battery-Box-Premium - LVS/LVM)
- Pylon (Force-L1)
- Fox (LV5200)
- LG Energy Solutions (Resu3.3, Resu 6.5, Resu10)
- Puredrive (PureStorage II Hybrid 5kWh)
- Green Solutions (Home E10)
- UZ Energy (Power Lite)
HOOG VOLTAGE BATTERIJEN:
BYD:
Battery Box Premium - HVS/HVM
HVS 5.1, 7.7, 10.2, 12.8
HVM 8.3, 11.0, 13.8, 16.6, 19.3, 22.1
Als u uw BYD batterij met Solis omvormers wilt verbinden, zijn de communicatiepoorten aan omvormer- en BMS-zijde als volgt:
CAN-H (Controller Area Network High) op Pin 1 (blauw)
CAN-L (Controller Area Network Low) op Pin 2 (blauw/wit)
PylonTech:
Force-H2
Als u uw Pylon batterij met Solis omvormers wilt verbinden, zijn de communicatiepoorten aan omvormer- en BMS-zijde als volgt:
BMS:
Communication Terminals:
Definitie van RJ45 Port Pin:
CAN-H (Controller Area Network High) op Pin 4 (blauw)
CAN-L (Controller Area Network Low) op Pin 5 (blauw/wit)
Soluna:
Module 10K Pack HV
BMS:
Zorg ervoor dat u de juiste COM Port (CAN 1 port) gebruikt.
De CAN communicatie interface voor Soluna batterij is als volgt:
CAN 1 poort voor inverter communicatie
WECO:
WeCo5K3-LV-HV
Als u uw Weco batterij met Solis omvormers wilt verbinden, zijn de communicatiepoorten aan omvormer- en BMS-zijde als volgt:
RJ45 port corresponding to the CAN bus pin definition
Dyness:
Tower Series
Als u uw Dyness Tower batterij met Solis omvormers wilt verbinden, zijn dit de communicatiepoort specificaties aan de BMS zijde:
BMS Interface:
1: Power/ Wake button
2: Battery connection positive
3: CAN Communication port
4: Battery connection negative
5: Power on switch
Pin definition for CAN communication:
LG Energy Solutions:
Resu 10H Prime
Cable connections:
Cable configuration:
Section A:
Inverter communication ports including CAN/RS485 and enable lines.
Section B:
DIP switch for setting communication termination resistor.
Section C:
DIP switch for setting primary/secondary packs.
Section D:
Do not connect the internal communication ports
Section E:
Battery power ports including positive/negative pole and ground (POS: power terminal plus, NEG: power terminal minus, GND: ground)
Guide for cable connection:
Communication ports:
- First, connect the enable ground wire to Terminal 2.
- Connect the enable 12V positive line to Terminal 1.
- Select the method that matches the inverter communication method in the part marked.
- If the inverter uses RS485, connect the RS485 (A+, B-) lines to Terminals 3 and 4. If inverter uses the CAN method, connect the CAN (high, low) lines to Terminals 5 and 6.
DIP switch for setting communication termination resistor of primary/secondary packs
Lower the DIP switch (Communication Termination resistor) all downwards for single pack.
LOW VOLTAGE BATTERIES:
BYD:
Battery Box Premium – LVS & LVM
LVS 5.1, 8.0, 12.0, 16.0, 20.0, 24.0
Connection diagram:
Pin assignment for BYD batteries:
PylonTech:
Force-L1
For those aiming to establish a connection between a Pylon Force L1 battery and Solis inverters, here are the communication port details on the BMS side:
Contol Module:
Definition of RJ45 Port Pin
Note: Other Pin must be NULL, if not it may influence the communication of the system.
Fox:
LV5200
BMS Interface:
J: CAN
K: RS485
L: Ground screw
M: LinkPort0
N: POWER-2
CAN / RS485 is the communication interface to the inverter. The interface is defined as follows:
LG Energy Solutions:
Resu3.3, Resu 6.5, Resu10
Connecting network cables:
Connect each network cable to its corresponding network port. Use the port at the lower left for the first battery pack, the one at the lower right for the second battery pack, and the one at the upper for the inverter.
Configuring the battery pack:
Remove the switch cover by pulling it up to expose the circuit board.
Settings for CAN bus pin:
Puredrive:
PureStorage II Hybrid 5kWh
Connection Interface:
- Battery<-->Inverter Power Cables(+)
- Battery<-->Inverter Power Cables(-)
- Communication cables(up)
- Communication cables(down)
- Battery reset button
- DC Isolator
- Grounding Point
Please use the provided communication cable
Connect communication cables as shown below. Plug in the COM resistor to the last communication interface, which is open.
Please note that even with a single battery installation or multi battery installation, COM resistor is required to strength the CAN Bus signal.
8. Communication cable
9. COM resistor
Plug in COM Resistor Put on protective cap
Green Solutions Inc.:
Home E10
To interconnect your Green solutions battery with Solis inverters, please note the following communication port settings on the BMS side:
Communication Terminals:
UZ Energy:
Power Lite
Battery Interface:
1: SOC LED x4
2: Alarm LED
3: RUN LED
4: Dialer
5: Communication port RJ11 RS232 To upper machine
6: Communication port *2 RJ45 CAN To PCS RS485 Internal Connection
7: Reset Waken system from malfunction status
8: Dry Contact
9: Power On/Off Switch
10: Port Negative x2 PSR6XAB Black 5.7, 25 mm2
11: Port Positive x2 PSR6XBB Orange 5.7, 25mm2
12: GND M6 Yellow-Green, 10 AWG
RJ45 Port definition:
CAN:
- Pin 1: CAN-H
- Pin 5: CAN-L
- Pin 2, 3, 4, 6, 7: NC
- Pin 8: GND
RS485:
- Pin 1, 4, 5: NC
- Pin 2, 7: RS485-A
- Pin 3, 6: RS485-B
- Pin 8: GND
RS232:
- Pin 1, 2, 6: NC
- Pin 3: BMS transmit; Computer receiver
- Pin 4: BMS receiver; Computer transmit
- Pin 5: GND
We hope that this information on connecting batteries to inverters proves helpful. If you have any further questions or specific battery requirements, please don't hesitate to reach out to us. We're here to assist you in any way we can.
Connect with Solis
Was dit artikel nuttig?
Dat is fantastisch!
Hartelijk dank voor uw beoordeling
Sorry dat we u niet konden helpen
Hartelijk dank voor uw beoordeling
Feedback verzonden
We stellen uw moeite op prijs en zullen proberen het artikel te verbeteren